機箱機柜的品質直接受制作工藝的好壞的影響，工藝較不錯機箱的鋼板邊緣不會泛起毛邊、銳口、毛刺等現象，并且裸露的邊角都經由折邊處理，不易劃傷裝機者的手。各個插卡槽位的定位也都相稱，不會泛起配件裝置不上或許錯位的為難狀況。

　　The quality of the chassis and cabinet is directly affected by the quality of the manufacturing process. If the process is good, the steel plate edges of the chassis will not have burrs, sharp edges, burrs, etc., and the exposed corners are all folded to prevent scratching the hands of the installer. The positioning of each card slot is also appropriate, so there will be no difficult situation of accessory devices not being installed or misplaced.

　　那么怎么選購機箱機柜呢？

　　So how to choose a chassis cabinet?

　　01

　　01

　　看架構布局

　　View architecture layout

　　一般來說，擋板要多，而且具有散熱孔，一些用來固定線纜的鐵皮要包邊，防預損壞線纜。側壁風扇應裝置在機柜后壁，由于設備后部產生大多數的熱量。

　　Generally speaking, there should be more baffles with heat dissipation holes, and some iron sheets used to fix cables should be wrapped to prevent pre damage to the cables. The side wall fan should be installed on the back wall of the cabinet, as most of the heat is generated at the rear of the equipment.

　　02

　　02

　　看功用

　　See function

　　先考慮的應是穩定性。

　　The first consideration should be stability.

　　03

　　03

　　看材料

　　Look at the materials

　　要挑選鈑金機箱機柜，一起鋼板改成要厚，你用手指敲一下，就能感覺到哪些厚哪些薄了。它堅實的外殼保護著板卡、電源及存儲設備，能防壓、防沖擊、防塵，并且它還能發揮防電磁攪擾、輻射的功用，起屏蔽電磁輻射的效果。再次，它還提供了許多便于運用的面板開關指示燈等，讓操作者愈方便地操作微機或觀察微機的運行狀況。

　　To choose a sheet metal chassis cabinet, change the steel plate together to make it thicker. You can feel which ones are thicker and which ones are thinner by tapping with your fingers. Its solid shell protects the board, power supply, and storage devices, and can prevent pressure, impact, and dust. It can also play a role in preventing electromagnetic interference and radiation, and has the effect of shielding electromagnetic radiation. Again, it also provides many user-friendly panel switches, indicator lights, etc., making it more convenient for operators to operate or observe the operation status of the microcomputer.

　　04

　　看噴漆

　　Look at the spray paint

　　一個合格的機柜，所有的鋼材都需求噴漆，而且噴漆改成要平均，這樣才能良好地防銹、防塵等。

　　A qualified cabinet requires all steel to be painted, and the painting should be evenly distributed to ensure good rust and dust prevention.

　　05

　　看散熱

　　Check the heat dissipation

　　估計一下你的設備發熱量有多大，一般來說，柜頂都有二到四個風扇，風扇都是多多益善的啦。還有一些用來固定機架的螺絲、螺母等，也要足量。不因日后擴展而帶來配件不足的麻煩。

　　Estimate how much heat your device generates. Generally speaking, there are two to four fans on the top of the cabinet, and the more fans there are, the better. There are also some screws, nuts, etc. used to fix the rack, which should be sufficient. Not causing the trouble of insufficient accessories due to future expansion.

　　06

　　看配件

　　Check the accessories

　　由于裝置中包含網絡電纜、電信電纜和電源電纜，需求購買鉤環帶或帶齒的帶子來地把電纜有序的固定在機柜里面。假設機柜帶有電纜管理模塊使電纜能夠直接固定在筆直裝置軌內，則再好不過。

　　Due to the inclusion of network cables, telecommunications cables, and power cables in the device, it is necessary to purchase hook and loop or toothed straps to orderly secure the cables inside the cabinet. It would be great if the cabinet had a cable management module that allows cables to be directly fixed in the straight device track.

　　07

　　看玻璃

　　Look at the glass

　　玻璃改成要厚一點的，還要留意玻璃的周邊是否有裂縫，假設有裂縫，就意味著有隱患了，還有要留意是否棘手。

　　Make the glass thicker and pay attention to whether there are cracks around the glass. If there are cracks, it means there are hidden dangers. Also, pay attention to whether it is difficult.

　　在散熱技術方面，機箱機柜設備降溫多數選用空調系統推送冷氣的方式，為了局部高熱去降溫整個空調系統的溫度往往將很低，提升電力機箱機柜的使用率。

　　In terms of heat dissipation technology, the cooling of chassis and cabinet equipment is mostly achieved by using air conditioning systems to push cold air. In order to reduce the temperature of the entire air conditioning system due to local high heat, the temperature is often lowered to a very low level, thereby improving the utilization rate of power chassis and cabinets.

　　便于制造

　　Easy to manufacture

　　01在同時達到技術要求的的基礎上，應依據各企業的現實生產，優先考慮制作工藝簡便的鈑金加工方法，以降低成本，提升生產速率。

　　01On the basis of meeting technical requirements simultaneously, priority should be given to sheet metal processing methods with simple manufacturing processes based on the actual production of each enterprise, in order to reduce costs and improve production rates.

　　盡量減少焊接

　　Minimize welding as much as possible

　　02 焊接后會引起變形，而且焊接外表料理不標致，波及生產速率，另外能夠改變工藝來替代焊接。1、利用鉚接來替代焊接，在節約時間的同時又能不變形。2、用沖壓來代替焊接，不宜變形，但有時要利用簡易模具。3、取消作用不大的焊接。對于受力小或僅起鏈接作用的焊縫，可采用間接斷焊來代替延續焊。壓鉚過程示意圖

　　Welding can cause deformation, and the welding surface is not aesthetically pleasing, affecting production speed. In addition, the process can be changed to replace welding. 1. Using riveting instead of welding can save time while avoiding deformation. 2. Using stamping instead of welding should not cause deformation, but sometimes simple molds should be used. 3. Cancel welding that has little effect. For welds with low stress or only serving as a link, indirect break welding can be used instead of continuous welding. Schematic diagram of riveting process

　　取材要正確，冷作鈑金的原材按材質分，有合金構造鋼，碳素構造鋼，鋁銅等。按軋制的斷面形狀特征分，有型材，板材，線材，型材。在挑選時應按以下幾點正確挑選：

　　The material selection should be correct. The raw materials for cold sheet metal are classified according to their materials, including alloy structural steel, carbon structural steel, aluminum copper, etc. According to the characteristics of the cross-sectional shape of rolling, there are profiles, plates, wires, and profiles. When selecting, the following points should be followed correctly:

　　03 1、提供原材料的利用率鈑金加工，在強度和技術要求的前提下，其胚料允諾以小拼大，這樣能夠減少邊角余料，降低成本，依據板材的大小，能夠選用訂好的尺寸長度的板材。2、依據工作情況正確挑取材料鈑金加工設計的活泛性大，具有許多的優良性冷作件的壁厚能夠相差很大，按受力情況不同和工作情況的不同，可選用不同強度、不同、等性能的材料。3、盡量采用軋制的型材經軋制的型材，尺寸較準確，品質，外表平整，光潤，價錢低，采用軋制的型材還能夠減少焊接及成型加工開銷，具率不錯，成本還行的優點，所以在構造件中能普遍的應用。

　　03 1. Provide the utilization rate of raw materials for sheet metal processing. Under the premise of strength and technical requirements, the raw materials are promised to be assembled in small sizes to reduce corner scraps and lower costs. Based on the size of the sheet metal, it is possible to select sheets of predetermined size and length. 2. The flexibility of selecting materials correctly based on work conditions in sheet metal processing design is high, and it has many excellent properties. The wall thickness of cold work parts can vary greatly, and materials with different strengths, properties, etc. can be selected according to different stress conditions and work conditions. 3. Try to use rolled profiles as much as possible. Rolled profiles have accurate dimensions, good quality, smooth appearance, and low price. Using rolled profiles can also reduce welding and forming processing costs, with good yield and reasonable cost. Therefore, they can be widely used in structural components.

　　本文由  濟南機箱機柜 友情奉獻.更多有關的知識請點擊  http://www.hua155.com/   真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Chassis Cabinet For more related knowledge, please click http://www.hua155.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.